Plumbing Basics: The First Step for Bathtub Installation

Find Out More

They are making a number of good annotation on A Step-by-Step Guide to Installing a Bathtub in general in this post following next.


How to Install a Bathtub Yourself
Installing a bathtub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a moderately challenging project. If the old bathtub is conveniently accessible, the job can move rapidly; if you need to open a wall to remove the old tub as well as place the new bathtub, the job is much harder. In either instance, the project is within a residence handyman's abilities, although you will need an assistant to move out the old bathtub and also embeded in the brand-new one. See to it you have qualified on your own for the job and also are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed job, it is better to take into consideration using one before you start. Chances are you might need a professional plumber to make tube links.
This short article will certainly aid you set up a brand-new bathtub in your shower room if you have already bought a new bathtub and don't require to change the arrangement of your previous water system pipelines.
Your tools as well as material list should consist of the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Planning for the Installation


    To start with, the sustaining frame supplied with the bath must be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to stop strain on the bathtub.
    Fit the flexible tap connectors to the bottom of both taps utilizing 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of all of the supplied washing machines.
    Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its final position.

    Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome because of the restricted gain access to that is typically the situation.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly originate from the pipelines. When the supply pipes have actually been removed, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this procedure. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
    Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

    Installing the Tub


    Making use of both wood boards under its feet, put the tub in the needed position. The wood boards are valuable in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
    The next objective is to make sure that the tub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the bath tub until the spirit level reads degree.
    To mount taps, fit all-time low of the outermost flexible faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the other faucet.
    Switch on the water system and check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and also the regular electrical outlet for leaks.
    Ultimately, take care of the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bath tub must wait up until the bath tub has actually been utilized at the very least once as this will resolve it into its last position.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
    If you need to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the faucet in place with the manufacturer offered backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former type ought to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Tiling Around the Bathtub


    In the area where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, creating the water to permeate the wall surface in between the bathroom and the tiling, resulting in complications with dampness and also feasible leaks to the ceiling below.
    You can select from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes as well as cartridges, and also can securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can split fairly very early if you do not take into consideration this activity before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof sticky and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    We were shown that article about How to Install a Bathtub Yourself through an associate on a different web page. Sharing is good. Helping people is fun. Thank-you for going through it.


    Toilet issues? Call!

    Leave a Reply

    Your email address will not be published. Required fields are marked *